Nirb's V24 Backup

Backup and of my Voron 2.4 350mm

discord: nirb_agga

---

Features and Mods

Current Features/Mods

• Voron TAP
• Canbus - EBB
• Nozzle Scrubber
• Input Shaping and Resonance
• Stealthburner with Clockwork 2
• Phaetus Dragon UHF
• Adaptive Bed Mesh
• Spoolman with moonraker's spoolman integration
• X Handle
• Logitech Cam Mount
• Voron Rollback
• Chamber Thermistor Mount
• Nevermore V5 Duo
• TFT50 Display Mount using this 45 Degree Mount
• LED Effects
• Disco Led
• Z-Chain Relocate
• Cable Clip

Planned Features/Mods

• GE5C
• Voron2.4 GE5C Z Joint Remix
• WLED macros with moonraker's wled component
• Probe Accuracy Tests - have to be run from command line
• Klipper Estimator
• Voron Klipper Extensions
• ERCFv2
• Happy Hare
• Pins Mod
• The Filter
• Nevermore Stealthmax
• BFI & BZI
• BFI Gears
• Snap Latches
• Annex Latches
• Hex Infill Skirts
• Hex Infill Screen Mount
• Hex Infill Pulley Cover
• Hotkey Buttons
• Lift Off Doors
• Tiny Door Handles
• Magnetic Bottom Panel
• CM4 Fan
• TMC2209 Fan
• Nevermore Controller

Other Cool/Possible Mods

• Disco LED Mount
• Corner Cable Cover
• Z Belt Clip
• Threaded Bowden Retainer
• Bowden Guide
• Cable Managment Ducts
• Cable Managment Ducts
• Cable Chain
• Cable Clip
• Cable Clamp
• Knomi Hex SB Face
• Bed Wagos
• Bed Wagos
• Voron CW2 Stealthburner EBB SB2240 PG7 Umbilical Mount
• ALT A Drive
• Rear Umbilical
• StealthBurner Face
• Y Endstop Relocate
• 221-415 WAGO Mount with Labels

Links

Main mod repos

• Voron User Mods
• https://voronregistry.com/mods
• https://vorondesign.com/

References/Documentaion

• Klipper
• KlipperScreen
• Moonraker
• Mainsail
• Esoterical CanBus Guide
• Voron Design
• Ellis' Print Tuning Guide

Other klipper backups/macros/repos I've found useful

• mjoconr
• Frix-x
• richardjm
• rkolbi
• 3DPrintDemon
• jschuh
• EricZimmerman
• hartk1213
• TmRxJD (KOMB)tree/main
• mystoopidstuff

Pi CM4 Configs

/etc/network/interfaces.d/can0

Show Interface Config

allow-hotplug can0
iface can0 can static
    bitrate 1000000
    up ifconfig $IFACE txqueuelen 1024
    pre-up ip link set can0 type can bitrate 1000000
    pre-up ip link set can0 txqueuelen 1024

/boot/firmware/config.txt

Show Config

# For more options and information see
# http://rptl.io/configtxt
# Some settings may impact device functionality. See link above for details
#oscillator=8000000
#tmp wifi off
dtoverlay=disable-wifi
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on
# Enable USB
#dtoverlay=dwc2,dr_mode=host
# Enable audio (loads snd_bcm2835)
#dtparam=audio=on

# Additional overlays and parameters are documented
# /boot/firmware/overlays/README

# Automatically load overlays for detected cameras
camera_auto_detect=1

# Automatically load overlays for detected DSI displays
#display_auto_detect=1

# Automatically load initramfs files, if found
auto_initramfs=1

# Enable DRM VC4 V3D driver
dtoverlay=vc4-fkms-v3d
#max_framebuffers=2

# Don't have the firmware create an initial video= setting in cmdline.txt.
# Use the kernel's default instead.
disable_fw_kms_setup=1

# Run in 64-bit mode
arm_64bit=1

# Disable compensation for displays with overscan
disable_overscan=1

# Run as fast as firmware / board allows
arm_boost=1

[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller.
# This line should be removed if the legacy DWC2 controller is required
# (e.g. for USB device mode) or if USB support is not required.
otg_mode=1

[all]