Python-VPP

3-DOF Velocity Prediction Program based on the ORC aero and hydro dynamic models.

Please see the demo hosted at https://yacht-vpp.streamlit.app/ and go for a test sail!

Using the code

The project is managed with uv. Install it once (see the uv docs for other methods):

curl -LsSf https://astral.sh/uv/install.sh | sh

Then clone the repository and install the dependencies into a local .venv:

git clone https://github.com/marinlauber/Python-VPP.git
cd Python-VPP
uv sync

The main files that are used are runVPP.py and righting_moment.json. These have to be filled with the data of your boat. By default they are using the YD-41 (from Principle of Yacht Design).

The VPP is run from the root of the repository with

uv run python runVPP.py

At each TWS/TWA the boat speed is maximised over boat speed, heel, leeway, sail flattening and reefing, subject to force and moment equilibrium (SLSQP). VPP.set_analysis takes an optional maximum heel angle (phi_max, default 35 degrees); the sails are only flattened (down to flat = 0.53) and reefed as much as is fastest within it, following the ORC VPP 2026 depowering scheme. Kites are further limited to their own max_heel (default 21.5 degrees, the ORC limit under spinnaker). Points where a sail set cannot be carried within its heel limit are left at 0 and not plotted. The apparent wind follows the ORC heeled wind triangle: TWS is taken at 10 m and scaled to the sail plan's centre of effort with a log wind profile (z0 = 0.005 m), and its cross-track component is reduced by cos(heel). Appendage drag follows the ORC strip friction, form factor and lift-dependent drag, and the induced drag the ORC rudder ramp (zero lift upright), heel multiplier and free-surface/funsteady span corrections. Appendage lift uses the geometric aspect ratio span²/area, doubled for the reflection in the hull, in a lifting-line lift-curve slope (Jones slender-wing slope for short keels). VPP.run accepts method="sequential" (default) or "parallel" (same results, spread over all CPU cores).

To run the Streamlit demo locally:

uv sync --extra demo --extra api
uv run streamlit run demos/Home.py

The run writes the results to results.json and saves the polars (Polars.pdf) and the sail chart (SailChart.pdf) as PDF, so the curves stay sharp when zoomed. For the YD-41 the polars look like this (Figure.png is a PNG copy of Polars.pdf for this page)

See the documentation.

Input variables

Here is a list of the key variables used in the VPP.

1. Appendages :
   • Cu : Root Chord / Upper Chord (m)
   • Cl : Tip Chord / Lower Chord (m)
   • Span : Span (m)
   • Tc_ratio : thickness/chord ratio for the ORC form factor (keel 0.20, rudder 0.10 by default)
2. Yacht :
   • Lwl : Length waterline (m)
   • Vol : Displ. volume of canoebody (m^3)
   • Bwl : Beam waterline (m)
   • Tc : Canoe body draft (m)
   • WSA : Wetted surface area (m^2)
   • Tmax : Draft max, i.e. Keel (m)
   • Amax : Max. section area (m^2)
   • Mass : Total mass of the yacht, including keel (kg)
   • Ff : Freeboard height fore (m)
   • Fa : Freeboard height aft (m)
   • Boa : Beam overall (m)
   • Loa : Length overall (m)
   • App : List of appendages
   • Sails : List of Sails
3. Sails: Standard measurements, except Roach is defined as 1-A/(0.5PE) HBI (jib) is the height of the base of I above the waterline; sail centres of effort (kite vce) are measured from it Kite only takes area and vce estimate (this is very rough), min_reef (default 0.85) for depowering and max_heel (default 21.5 degrees)
4. VPP.set_analysis()
   • TWA range : range of TWA to use
   • TWS range : range of TWS, must be between [2, 35]

Contributing

We are very keen to see contributions to code, documentation and feature development!

When you make a contribution please make sure that any new functionality is covered with additional tests.

Follow the steps below to contribute to this project.

Install dependencies

Install the project with the development tools (pytest, ruff, mypy) and the API dependencies:

uv sync --extra dev --extra api

Note that uv sync removes extras that are not listed, so pass every extra you need (or use uv sync --all-extras).

If using pip instead:

pip install -e ".[dev,api]"

Run tests

Tests are implemented using pytest.

You can run tests with

uv run pytest -vv

You can run a benchmark against the YD-41 results from WinVPP by running the benchmark.py script (-g saves the polars as one Figure_<label>_<TWS>.pdf per wind speed plus a Figure_<label>_stats.pdf error summary, -s saves the results).

uv run python benchmark/benchmark.py -g -s

Acknowledgements

• Otto Villani - Initial idea, model selection - GitHub
• Marin Lauber - Initial idea, development - GitHub
• Thomas Dickson - Developer - GitHub

License

This project is licensed under the MIT License - see the LICENSE file for details