Mutant is a generative synth that uses an Arduino Nano. The synth design and the code are by Meebleeps. I designed a PCB and a front panel, so that it fits in a Eurorack case. You can also use it as a standalone synth.
- Step-by-step build guide on Instructables: Mutant Generative Arduino Synth
- Video on YouTube: Mutant
The synth voice has 2 saw oscillators, with:
- Tuning modes for the second oscillator: off, detune, fifths, and octaves up or down
- Low-pass filter with cutoff and resonance controls
- Ducking (sidechain) effect with a level control
An 8 × 8 LED matrix shows the level of each control. The 16-step generative sequencer changes (mutates) at a rate that you set. It has:
- Mutation probability and note-density controls
- Sync input and sync output (compatible with Korg Volca)
- Note selection
- Scale quantization: major, minor, pentatonic, Phrygian, octaves and fifths
- 16-step parameter-lock recording
- A retrigger (clone) button for fills
- Tap tempo
Power: 9 V to 12 V, from a Eurorack power connector or a 9 V supply.
- All parts are in the parts list.
- The schematic is Schematic.png.
- The Gerber files for the PCB and the front panel are in Gerber Files. You can send them to a PCB maker.
- Arduino IDE
- The Mozzi library. The version that you need depends on the sketch. See the next section.
There are two sketches in Mutant_IDE_Code/. They make the same sounds.
| Sketch | Mozzi version | Use it when |
|---|---|---|
Mutant_Updated |
Mozzi 2 (the current version) | Recommended. Use this sketch. |
Mutant_Original |
Mozzi 1.1.2 (old version) | Only if you already use Mozzi 1.1.2 |
- Download this repository. Click Code → Download ZIP, then extract the ZIP file.
- In the Arduino IDE, open the Library Manager.
- Search for Mozzi and install the newest version.
- Open
Mutant_IDE_Code/Mutant_Updated/Mutant_Updated.ino. - Connect the Arduino Nano to your computer with a USB cable.
- In the Tools menu, set these values:
- Board: Arduino Nano
- Processor: ATmega328P
- Port: the COM port of your Nano
- Click Upload.
- Wait for the message Done uploading.
Note: If the upload fails, set Processor to ATmega328P (Old Bootloader), then try again. Many clone Nano boards need this setting.
Note: To use
Mutant_Original, install Mozzi version 1.1.2 in step 3. In the Library Manager, select 1.1.2 in the version list, then click Install.
The controls are described in the Meebleeps Mutant Synth README.
| Folder or file | Contents |
|---|---|
Mutant_IDE_Code/ |
Firmware: the updated sketch and the original sketch |
Eagle Files - PCB/ |
Eagle files for the PCB |
Front Panel Design/ |
KiCad, Inkscape and PNG files for the front panel |
Gerber Files/ |
Gerber files for the PCB and the front panel, ready to order |
Parts List/ |
Parts list |
Schematic.png |
Schematic |
I want to make my own modular synth that is simple to build. Each module has these aims:
- It operates from 9 V (and 12 V).
- It is easy to build, with a minimum of components.
- It uses an Arduino, to keep the parts count low and everything in tune.
- It fits in any Eurorack case, and it can use normal Eurorack power.
- It sounds good.
- It is portable, and it can operate from a 9 V battery.
- Synth design and code: Meebleeps Mutant Synth. Thank you, Meebleeps.
- Audio library: Mozzi.
- PCB, front panel, Eurorack version and the Mozzi 2 update: Marcus (lonesoulsurfer).
Do you like this project? You can support my work on GitHub Sponsors.
This project uses the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License (CC BY-NC-SA 4.0), the same licence as the Meebleeps original.
- You can build, share and change this project.
- You must name Meebleeps and lonesoulsurfer.
- You must not use it for commercial purposes. For example, do not sell kits or built synths.
- If you share a changed version, you must use the same licence.

