You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
{{ message }}
Repository navigation
Y2 stuttering over Bluetooth with Bush SR210-12 Bluetooth Soundbar when Y2's WiFi enabled #99
My Skullcandy Dime 2 Bluetooth Earbuds and my SONRU Bluetooth Audio Receiver work as expected, but my Bush SR210-12 Bluetooth Soundbar has been stuttering, as in the clip attached to my Reddit reply.
I'm still having an issue after 9.3.16 and I've discovered it could be linked to the Y2's WiFi being on. If I turn WiFi off and reconnect the soundbar via Bluetooth, it seems to play normally
This could be to do with whatever happens when my Y2 first starts playback after connecting to the Bush soundbar via Bluetooth
It could also relate to distance from the soundbar, because it was less likely to skip when on my desk right next to the soundbar
If my knowledge on WiFi in devices serves me right, sometimes the same chip
deals with Bluetooth as WiFi. This is how my laptop works and I wouldn't be
surprised if that's true for the Y2 too.
There might be a data buffer chip-wide that WiFi + Bluetooth is filling too
quick.
Thanks for the reports and the clip, and sorry for the wait.
What the reports show: on the player's side the stream is clean: no gaps, no codec errors, and the soundbar runs SBC at its highest setting (the player's lowest SBC choice is "High"). The soundbar dropped the link twice, and it took several attempts to connect at first. Both fit a weak radio link between the player and the soundbar, which also matches what you noticed about distance. One small thing: in the report you sent after the "Wi-Fi off" test, Wi-Fi was on at that moment, so that test may not have been fully without Wi-Fi.
New in the next update (Beta 9.3.20): an SBC Auto Rate switch. With it on, the player lowers SBC's data rate whenever the link can't keep up, and raises it again once it can. The setting is in the service menu: Settings → System → About, tap Version seven times, then SBC Auto Rate. Restart the player after changing it.
After the update, could you try with SBC Auto Rate on, first with Wi-Fi off (Settings → Wi-Fi off), then on? A report after a stutter with it on would show how often it had to step down. I'm leaving this open until we know whether it helps.
SBC Auto Rate is in Beta 9.3.20: Settings → System → About, tap Version seven times, then Diagnostics → SBC Auto Rate. It's off by default. If you can, please try your soundbar with it on, with Wi-Fi on, and tell me whether the stuttering changes.
I've sent an error report now within the Y2 over wi-fi
The new update seems to have helped with BT playback, especially if I let the player sit untouched in front of the speaker. It will still stutter if I pick it up to check the screen or if I press the side screen on/off button. Is that shown in the error report?
Thanks for the report. With SBC Auto Rate on, the player stepped the rate down twice in under two minutes and the connection never dropped, so it is doing its job. What the report couldn't tell me is when a stutter happened.
Beta 9.3.24 changes that: it records each rate step with its time, so a report sent right after a stutter shows what the link did at that moment.
To separate the two things you noticed, could you update and try these (answering by number is fine):
Player lying still in front of the soundbar, you only press the screen button: does it stutter? [yes / no]
Screen left alone, you only pick the player up: does it stutter? [yes / no]
The same two tests with Wi-Fi off (Settings → Wi-Fi): any difference? [yes / no / not tried]
Then please send an error report right after a stutter.
The error report I've just sent is unrelated to the Bluetooth/stuttering issue. I sent it because Windows Explorer kept closing on me while I was trying to copy the system.img file for FM radio. Eventually, I got system.img copied over using a different USB port on my PC
I will check the Bluetooth/stuttering and send a further error report after that if needed
A friendly nudge: did you get a chance to try the three tests from my last comment (screen button only / picking it up only / both with Wi-Fi off)? Since 9.3.24 a report sent right after a stutter shows what the link did at that moment.
If I don't hear back in about a week I'll close this, and you can reopen it any time.
I've just had a look now, but the menu options seem to have changed in one of the latest updates.
Is the SBC Auto Rate settings one of these in Diagnostics > Bluetooth?
The 2 error reports I've just sent aren't a test of SBC Auto Rate, but I hope they'll show you where the player stuttered, which I fixed temporarily by restarting my Y2
Thanks for all the testing. Your two reports from today settle it: at 09:47 SBC Auto Rate stepped the rate down six times in 20 seconds, and Wi-Fi was off the whole time (you switched it on at 09:48 to send the reports). So it isn't Wi-Fi. It's the radio link to the soundbar, which gets worse when the player is picked up or moved. There were no gaps or errors on the player's side.
Where we are: Y2Linux already does what a phone does: it lowers the data rate when the link struggles, keeps Bluetooth off the Wi-Fi channel, lets Wi-Fi rest while music streams, limits the catch-up after a dropout and fills gaps with silence. I've worked through every Bluetooth report again, and the player's side is clean in all of them. What's left is the hardware: the Y2 has one small radio that shares its antenna with Wi-Fi, and it just can't hold a link the way a phone can. We've reached the ceiling of what software can do here.
Honestly, if you want music without dropouts on the Y2, I'd recommend wired headphones.
Beta 9.3.34 adds one last thing: each stall of the Bluetooth link is now written down, so if something new ever shows up, a report will say when and how long. More in the 9.3.34 report. I'm closing this; thanks a lot for the reports and the patience.
Activity
Iron-Wolf-23 commentedon Nov 7, 2026
Report sent
This could be to do with whatever happens when my Y2 first starts playback after connecting to the Bush soundbar via Bluetooth
It could also relate to distance from the soundbar, because it was less likely to skip when on my desk right next to the soundbar
RockinProjex commentedon Nov 8, 2026
kchiem commentedon Nov 8, 2026
OP, I think you failed to submit the report ID.
Iron-Wolf-23 commentedon Nov 8, 2026
Does this work?
Install ID is 90B5ABF3
y2linux-report-20261108-190934.tar.gz
I tried the soundbar this evening via Bluetooth with WiFi off and the sound was still cutting out
SchulzCode commentedon Nov 9, 2026
Thanks for the reports and the clip, and sorry for the wait.
What the reports show: on the player's side the stream is clean: no gaps, no codec errors, and the soundbar runs SBC at its highest setting (the player's lowest SBC choice is "High"). The soundbar dropped the link twice, and it took several attempts to connect at first. Both fit a weak radio link between the player and the soundbar, which also matches what you noticed about distance. One small thing: in the report you sent after the "Wi-Fi off" test, Wi-Fi was on at that moment, so that test may not have been fully without Wi-Fi.
New in the next update (Beta 9.3.20): an SBC Auto Rate switch. With it on, the player lowers SBC's data rate whenever the link can't keep up, and raises it again once it can. The setting is in the service menu: Settings → System → About, tap Version seven times, then SBC Auto Rate. Restart the player after changing it.
After the update, could you try with SBC Auto Rate on, first with Wi-Fi off (Settings → Wi-Fi off), then on? A report after a stutter with it on would show how often it had to step down. I'm leaving this open until we know whether it helps.
radiod: after a sleep without a headset, wake looks for headphones on…
docs: Beta 9.3.20 (sequence 15400): report for owners (audiobook butt…
SchulzCode commentedon Nov 10, 2026
SBC Auto Rate is in Beta 9.3.20: Settings → System → About, tap Version seven times, then Diagnostics → SBC Auto Rate. It's off by default. If you can, please try your soundbar with it on, with Wi-Fi on, and tell me whether the stuttering changes.
docs: Beta 9.3.21 (sequence 15700): report for owners (Bluetooth on a…
Iron-Wolf-23 commentedon Nov 10, 2026
I've sent an error report now within the Y2 over wi-fi
The new update seems to have helped with BT playback, especially if I let the player sit untouched in front of the speaker. It will still stutter if I pick it up to check the screen or if I press the side screen on/off button. Is that shown in the error report?
radiod: the encoder's rate over time: while a Bluetooth stream plays,…
SchulzCode commentedon Nov 11, 2026
Thanks for the report. With SBC Auto Rate on, the player stepped the rate down twice in under two minutes and the connection never dropped, so it is doing its job. What the report couldn't tell me is when a stutter happened.
Beta 9.3.24 changes that: it records each rate step with its time, so a report sent right after a stutter shows what the link did at that moment.
To separate the two things you noticed, could you update and try these (answering by number is fine):
Then please send an error report right after a stutter.
Iron-Wolf-23 commentedon Nov 13, 2026
The error report I've just sent is unrelated to the Bluetooth/stuttering issue. I sent it because Windows Explorer kept closing on me while I was trying to copy the system.img file for FM radio. Eventually, I got system.img copied over using a different USB port on my PC
I will check the Bluetooth/stuttering and send a further error report after that if needed
SchulzCode commentedon Nov 17, 2026
A friendly nudge: did you get a chance to try the three tests from my last comment (screen button only / picking it up only / both with Wi-Fi off)? Since 9.3.24 a report sent right after a stutter shows what the link did at that moment.
If I don't hear back in about a week I'll close this, and you can reopen it any time.
Iron-Wolf-23 commentedon Nov 17, 2026
I've just had a look now, but the menu options seem to have changed in one of the latest updates.
Is the SBC Auto Rate settings one of these in Diagnostics > Bluetooth?
Iron-Wolf-23 commentedon Nov 19, 2026
The 2 error reports I've just sent aren't a test of SBC Auto Rate, but I hope they'll show you where the player stuttered, which I fixed temporarily by restarting my Y2
SchulzCode commentedon Nov 19, 2026
Thanks for all the testing. Your two reports from today settle it: at 09:47 SBC Auto Rate stepped the rate down six times in 20 seconds, and Wi-Fi was off the whole time (you switched it on at 09:48 to send the reports). So it isn't Wi-Fi. It's the radio link to the soundbar, which gets worse when the player is picked up or moved. There were no gaps or errors on the player's side.
Where we are: Y2Linux already does what a phone does: it lowers the data rate when the link struggles, keeps Bluetooth off the Wi-Fi channel, lets Wi-Fi rest while music streams, limits the catch-up after a dropout and fills gaps with silence. I've worked through every Bluetooth report again, and the player's side is clean in all of them. What's left is the hardware: the Y2 has one small radio that shares its antenna with Wi-Fi, and it just can't hold a link the way a phone can. We've reached the ceiling of what software can do here.
Honestly, if you want music without dropouts on the Y2, I'd recommend wired headphones.
Beta 9.3.34 adds one last thing: each stall of the Bluetooth link is now written down, so if something new ever shows up, a report will say when and how long. More in the 9.3.34 report. I'm closing this; thanks a lot for the reports and the patience.
docs: not planned: more Bluetooth range or stability than the Y2's ra…